收藏本站
MAX6948B
High-Efficiency PWM LED Driver with Boost
Converter and Five Constant-Current GPIO Ports
PWM Intensity Control and Phasing
The MAX6948B uses an internal 31.25kHz oscillator to
generate PWM timing for LED intensity control. A PWM
period comprises 256 cycles of the nominal 31.25kHz
PWM clock (Figure 2). Each port can have an individual
PWM duty cycle between 3/256 and 254/256. See Table
7 for port register settings.
Configure PWM timing by setting the stagger bit in the
configuration register (Table 2), either with output stag-
gering or without. Set PWM stagger = 0 to cause all
outputs using PWM to switch at the same time using the
timing shown in Figure 2. All outputs, therefore, draw
load current at the exact same time for the same PWM
setting. This means that if, for example, all outputs are
OUTPUT
REGISTER
set to 0x80 (128/256 duty cycle), the current draw would
be zero (all loads off) for half the time, and full (all loads
on) for the other half.
Set PWM stagger = 1 to stagger the PWM timing of the
five port outputs and the integrated boost-converter out-
put, distributing the port output switching points across
the PWM period (Figure 3). Staggering reduces the di/dt
output-switching transient on the supply and reduces the
peak/mean current requirement.
Change the PWM stagger-setting bit during shutdown.
Changing the stagger bit during normal operation can
cause a transient flicker in any PWM-controlled LED
because of the fundamental PWM timing changes.
VALUE
0x00
0x01
0x02
0x03
0x04
0xFC
0xFD
0xFE
0xFF
7.8125ms NOMINAL PWM PERIOD
OUTPUT STATIC-LOW LOGIC DRIVE WITH INPUT BUFFER ENABLED (GPI)
OUTPUT STATIC-HIGH LOGIC DRIVE WITH INPUT BUFFER ENABLED (GPI)
OUTPUT STATIC-LOW CONSTANT CURRENT WITH INPUT BUFFER DISABLED (STATIC LED DRIVE ON)
OUTPUT LOW 3/256 DUTY CONSTANT CURRENT WITH INPUT BUFFER DISABLED (PWM LED DRIVE)
OUTPUT LOW 4/256 DUTY CONSTANT CURRENT WITH INPUT BUFFER DISABLED (PWM LED DRIVE)
OUTPUT LOW 252/256 DUTY CONSTANT CURRENT WITH INPUT BUFFER DISABLED (PWM LED DRIVE)
OUTPUT LOW 253/256 DUTY CONSTANT CURRENT WITH INPUT BUFFER DISABLED (PWM LED DRIVE)
OUTPUT LOW 254/256 DUTY CONSTANT CURRENT WITH INPUT BUFFER DISABLED (PWM LED DRIVE)
OUTPUT STATIC HIGH IMPEDANCE WITH INPUT BUFFER DISABLED (STATIC LED DRIVE OFF)
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
HIGH-Z
LOW
Figure 2. Static and PWM Constant-Current Waveforms
16
Maxim Integrated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX6964ATG+T IC LED DRIVER LINEAR 24-TQFN
MAX6965ATE+T IC LED DRIVER LINEAR 16-TQFN
MAX6967ATE+ IC LED DRIVER LINEAR 16-TQFN
MAX6968AAE+ IC LED DRIVER LINEAR 16-SSOP
MAX6970AUE+ IC LED DRIVER LINEAR 16-TSSOP
MAX6971AUG+T IC LED DRIVER LINEAR 24-TSSOP
MAX6974ATL+ IC LED DRIVER LINEAR 40-TQFN
MAX6977AAE+ IC LED DRIVER LINEAR 16-SSOP
相关代理商/技术参数
MAX694C/D 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694CPA 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694CPA+ 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694EJA 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694EPA 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694EPA+ 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694MJA 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX694MJA/883B 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel